| |
|
|
 |
T-Case Crossmember, 4 cyl, 1979-83
Model: 120004-1-K
If you have dual transfer cases on your Toyota Surf or HiLux you will want to protect them from trail damage with a crossmember that can take serious trail punishment. Trail-Gear's crossmembers are precision laser cut with slotted mounting holes for easy bolt on installation. Made from 3/8" thick plate steel with black powdercoat finish. Includes tapered bolts for a smooth bottom. Fits 1979-1995 Toyota HiLux or Surf with dual transfer case.
Some minor scratching of the powder coating may occur during shipping and handling.
|
 |
|
T-Case Crossmember, 4 cyl, 1984-95
Model: 120005-1-K
As above.
|
NZ$620.00
 |
|
T-Case Crossmember Kit V6, 1987-95
Model: 120014-1-kit
As above
|
|
|
Trailer D-Ring 5/8 Inch
Model: 183001
Ideal for creating
tie down points on trailers. Welds in place.
Super tough, heavy-duty forged design.
- 5/8" Ring
Diameter
- Capacity: 18,000
lbs.
- Working Load
Limit: 6,000 lbs
- 4 3/8" overall
width
|
|
|
Shackle D-Ring 3/4 Inch
Model: 181003
D-Ring shackles make a
great pull point for vehicle recovery. Working Load
Limit 4 3/4" ton.
|
|
|
Weld-On Differential Armour - Small
Model: 120002-1
Here is a great way to
add some beef to the axle housing and protect your
ring gear from trail damage. This weld on plate is
curved to fit snugly over the face of your solid
axle housing. Made from 1/4" thick plate steel. Fits
front or rear 79-95 8" Toyota solid axle housings. Also
fits 91-97 front FJ-80 axle.
|
NZ$68.00
|
|
Weld-On Differential Armour - Large
Model: 120006-1-K
Here In addition to our
small style ring gear protector above we also have
this larger style for those that prefer something a
little larger to protect their 3rd member. Armor
welds in place. Includes two 10mm style drain plugs.
Fits front or rear 79-95 8" Toyota solid axle
housings. Unpainted finish.
|
NZ$86.00
|
|
Axle Gussett, Upper
Model: 110027-1
This gusset welds
on top of your Toyota front solid axle
and helps
prevent bending of
the axle housing.
|
NZ$68.00
|
|
Aluminium Fairlead, Billet, 10 inch centres
Model: 183500
Polished
aluminum hawse fairlead. Designed for use
with synthetic winch rope. Mounting holes
are 10" on center for standard 3/8" bolts,
compatible with most 5,000-9,500lb winches.
Ultra smooth guide surface (rounded on both
sides) to prevent damage to rope.
|
NZ$135.00
|
|
Toyota Bumper Plate (Bumper Winch Mount)
Model: 120021-1-Kit
If your
looking at building your own front bumper this mount
makes a great starting point. This winch mount bolts on
to the six factory holes found on 1984-1988 Pickups and
1984-1989 4unners. 1984-1985 body style requires
drilling two additional holes in plate. Made from 1/4" plate steel.
Also fits 1989-1995 models at four attachment points. Two inch
receiver tubing is also included. Plate is pre drilled
for 5000-9500 low profile winches. Also includes holes
for 9.0R Warn competition winch. Designed for use with
steel or aluminum hawse fairlead. When building bumper,
additional mounting points from bumper to frame are
required if used for heavy winching. If using a winch
with an integrated solenoid, such as the Warn 9500,
trimming of the front plastic grill will be necessary.
Unpainted finish.
|
|
|
Rock Slider Kit - 58 inch, DOM Tubing
Model: 120001-1-K
Rock Sliders are a great way
of protecting the rocker panels of your pickup or
4Runner. Made from 1 3/4" X .120 round HREW tubing. Legs
can be be cut to length to allow for different
mounting positions.
Rock Sliders are a great way
of protecting the rocker panels of your Tacoma pickup or
4Runner. Heavy duty design can take a pounding from the
rocks while keeping body damage to a minimum. Strong
enough to take the entire weight of the truck. A
high-lift jack can be used anywhere along it's length
for repositioning of rig or axle servicing. Sold in
pairs. Made from 1 3/4" X .120 round tubing.
Bars come with the outer section welded but the legs are
not attached. Legs are pre-notched and can be be cut to length to allow for different
mounting positions.
Note: 58" & 67" Rock
Sliders are now made from seamless DOM material. 78"
sliders are made from HREW material.
|
NZ$378.00
|
|
Rock Slider Kit - 67 inch
Model: 120002-1-K
Details as per 58 inch sliders
|
|
|
Rock Slider Kit - 78 inch
Model: 120003-1-K
As per 58 inch sliders.
Note: 58" & 67" Rock
Sliders are now made from seamless DOM material. 78"
sliders are made from HREW material.
|
|
|
Rock Slider Mounting Kit - 6 Leg
Model: 120007-1-K
Our gusset kits include
plates for the frame and triangle corner gussets. Plate
welds to frame and rock slider welds to plate. Kits are
made from 3/16" plate steel. 58" and 67" kits contain 6
plates and 6 gussets. 78" kit includes 8 plates and 8
gussets.
|
NZ$54.00
|
